Your shopping cart is empty.

  • EnglishNorwegian

Solinst Modell 408 Dobbel-ventilpumper

Solinst dobbeltventilert pumpe (DVP) er en pneumatisk drevet pumpe som gir konsistente høykvalitetsprøver

  • Kan leveres med 1,66-tommers eller 5/8 tommers diameter, eller som 3/8-tommers Modell 408 Micro DVP
  • Passer for prøvetaking med lav- eller middels strøm på dybder opp til 150 m (500 fot)
  • Kan benyttes sammen med Solinst Modell 464 pumpestyring, kompressor, slange, filter og pakninger for et komplett system


The Solinst Double Valve Pump (DVP) is a pneumatic drive pump that allows consistent, high quality samples. It has been field proven in thousands of applications.

It offers excellent performance and reliability. No bladder replacement is required, and the Double Valve Pump provides higher pumping rates than with the Solinst Bladder Pump. There is a selection of sizes and materials, variable flow rates, and it is field serviceable.

The DVP is suitable for low flow or regular flow sampling. The stainless steel pumps can operate to depths of 500 ft (150 m).

  • Easy Decontamination: Everything is easily accessible or replaceable without the need for tools. All components can be cleaned with mild detergent or non-phosphate soap.
  • Survives Dry Pumping, Dirty Air and Sand: Solinst bladders are not damaged by operation in sediment laden water, or in dry pumping conditions.
  • Saves Time and Costs: Low flow sampling reduces purge volumes and the time it takes to obtain a sample. There is less need for repeated sampling, which reduces the time needed for each sampling round.
  • Part of a Simple System: The air compressor or tank, pump controller, and flowthrough cell are easily transported to each site with the DVP. Compression fittings, quick-connect, and push-fit connections allow simple attachment to well caps or portable reels.
  • Low Flow Sampling: Gives excellent VOC retention, comparable with bladder pump results. When using the Solinst Model 464 Electronic Pump Controller, the DVP can be adjusted to provide a continuous output of 100 ml/min or less.
  • Non-Vertical Applications: Operates effectively at almost any angle and can be placed under landfills, tailings, storage tanks or plumes.
  • Leachate/Product Pumping: Pneumatic drive pumps may be used for pumping contaminant liquids. High solids content, solvents, hydrocarbons, and other chemicals are easily and economically pumped.
Pump Operation

When the pump is placed in a well or borehole, water rises inside the pump and the tubing to static level. Gas supplied from the Controller pushes down on the water column contained in the drive line tubing, closing the check valve at the base of the pump. This forces water up the sample line tubing.

A vent period, during which the gas is released, allows hydrostatic pressure to refill the pump and drive line with sample water. The top check valve prevents water in the sample line from falling back into the pump body. This pressurization and vent cycle is repeated to bring water to the surface.

For proper collection of volatiles, the pressure applied must never be high enough, nor the drive period long enough, to enable gas to enter the body of the pump and aerate the sample. If operated properly, “air” will never come in contact with the sample water, which produces high quality VOC samples comparable to those of a bladder pump.

Flow rates vary with depth of pump below surface, depth below water level, size of drive and sample tubing, drive and vent cycle times, gas pressure applied, aquifer recharge, and size of pump body.

  • Number of installations
  • Portable use or dedicated installation
  • Pump size (1.66-inch or 5/8-inch, or 3/8-inch Micro model)
  • Well cap size (2-inch or 4-inch for dedicated systems)
  • Tubing type (bonded natural LDPE or bonded FEP-lined LDPE)
  • Tubing length
  • Filters, packers, other accessories desired

Nylig Sett